How To Replace A Kitchen Faucet With Sprayer

Today’s kitchen faucets are so easy to install that just about anybody with a little DIY initiative can pull it off. When it comes to kitchen or bathroom faucets no matter how expensive it is or how good the material is you might need to replace them if they become a disturbance. But even if you are completely unaware of the procedure you can do it on your own by simply following the how to replace a kitchen faucet with a sprayer in minutes. 

To replace a kitchen faucet with a sprayer you need to remove the old faucet settings first. When the sink is ready you can install the few faucets, tighten all the screws, connect the water lines and give everything a final check. And for the sprayer take out the old sprayer and install the new one by screwing all the nuts and connecting the hose line. 

Here we’ve mentioned all kins of the installation process of faucet parts and their replacement processes, and also answered some of the most asked questions that mighty have asked. So if you want to know the anatomy of a faucet you should give this piece a thorough reading. 

4 Easy Steps To Know How To Replace A Kitchen Faucet With Sprayer?

When you need to replace your faucet, it can be pretty overwhelming and intimidating. But we are going to walk you through this entire process with very easy instructions that anyone can follow and apply. So keep on reading down below:

Step 1

Shut off the water supply for both the hot and cold water. There is a gasket that holds all the hose pipes together so unscrew all the nuts. For the brass threaded nut called fattening nut use a wrench to loosen it. Pull out the hose pipes. Take out the weight of the sprayer. 

Slide the installation tool through the hose to loosen the gasket nut. Take off the gasket and use a wrench to loosen the supply valves. Now you can pull out the entire faucet assembly. 

Step 2

Now prep the installation for the new faucet. Place the faucet gasket in position and insert the new faucet hose through the hole. Now under the sink slide the shaft gasket through the hose and use the installation tool to tighten the shaft. 

Step 3

Now feed your faucet hose through the faucet and that will snap into the fixture down below. Now underneath the sink take off the cap from the sprayer hose. Now connect the sprayer hose to the sink. To add the weight, open it up and there will be a little dummy barrel in there. Take that out. Now place it in the hose and snap it off. 

Step 4

Connect all your hot and cold water lines back up. Thread the applied valves back on. And tighten them with a wrench. Lastly, open the water valves and check for water leakings. Now put on the sprayer hose head. Take off the protective piece and thread it on. Hand tighten first and then use a wrench. 

Video Source: The Home Depot

Faucet Cartridge Types 

Most manufacturers offer different types and models of their faucet cartridges but their main purpose is the same which is replaceable and control the water flow and the temperature. But mostly there are two kinds of faucet cartridges for any kind of faucet. They are

Ceramic disk lab cartridgeThe Ceramic disk lab cartridge is a commonly used cartridge that comes in several different ways like polyester coated solid brass cartridge. There are glass-ceramic disks inside the cartridge. When to turn the stem you’ll see the disks opening and closing. 
But when it’s in the process if debris gets inside and you try to force close the disc might break. Because here two ceramic glasses are sandwiched together where the split lines align for water flow.
The cartridge faucet The regular cartridge faucet is made of durable brass or plastic. They mostly come in a variety of styles, materials, and sizes. 

How To Replace A Kitchen Sink Sprayer (2 Simple Steps)

When a kitchen sink sprayer starts leaking or the water flow is off then you might need to fix it or if it’s too old you can change it. So when you need to replace that leaky sprayer you can follow the easy steps down below:

Step 1 

First, turn off the water supply and place a towel underneath your sink, and press the sprayer trigger to release pressure. Follow the sprayer hose and you” ll see that it connects underneath the faucet.

If it has a blue clip on it then grab the clip and pull it out to unlock the hose. Twist back and forth slightly while pulling down to release the hose. It is normal to spill out little water. Pull the old sprayer up and out.

Step 2

Feed the new hose down the hole. If you feel any resistance while reinserting the hose, be sure the retaining clip is pulled straight out. Push the end of the hose all the way in and squeeze the clip until it snaps into the locked position. Turn the water supply back on and check for any possible leaks. 

How To Replace A Kitchen Faucet Sprayer Hose

If your kitchen faucet sprayer is leaking or if it is difficult to operate then you might be thinking of replacing it. So if you don’t know the steps you might like the steps that we’ve explained here for an easy replacement that you can do in minutes. To complete this project we recommend having a wrench on hand:

  • First, turn the water supply off to your faucet. Now find the connection and disconnect the spray hose from the high-pressure hose underneath. Unthread the hose, make sure you pull slowly so it does not catch the bottom fittings of the hose on the hose guide
  • Next, remove the weight from the hose and pull it out from above the counter. If you are replacing the spray head on a new hose now is the time to do that. If not continue by inserting the new hose from above the counter
  • Place the weight on the hose. Now thread the hose into place until it’s tight and secure it with a quarter turn with a wrench and your work is complete

How To Replace A Single Handle Kitchen Faucet

To complete this project you’ll need- a screwdriver, an adjustable wrench, and the wrench which is included in the box. Here we have discussed a single-handle diamond seal technology faucet with a pull-down sprayer. 

With the water supply turned off take out your old faucet setting first and get ready for installing the new one with the needed tools. Now fee the flexible spray hose through the spout and then the hub making sure you have the hose and spout running in the right direction. 

Now align the hose in the back of the spout with the clip on the hub and work it on with a back and forth motion until it snaps in place. Attach the sprayer at the hose end and the hand tightens the connection. Now you’ll need a faucet that has an escutcheon and gasket to mount your new faucet or you can order one from the manufacturer. 

Insert the faucet through the mounting hole of the sink. Take the mounting bracket and slide the hole over the shank. The supply lines should fit within the u-shaped bracket. Screw the nut at the end and tighten it. 

Slide down the hose weight and push the end onto the faucet outlet. Then place the clip over the connection to hold everything in place. Lastly, attach the water supply line carefully. 

How To Replace A Faucet Cartridge Single Handle

  • Close the shutoff valve and drain the faucet lines
  • With a screwdriver unscrew the screw cover and remove the handle screw and pull off the handle
  • Use channel lock pliers to unscrew the cap and the bonnet nut to remove the old cartridge
  • Make sure the rubber gasket is placed correctly in the new cartridge and align the pins in the cartridge to the holes in the base
  • Replace the bonnet nut and tighten it with pliers and set the tab to the full flow
  • Now hand tightens the cap and screw the handle back on and replace the screw cover
  • Finally, open the shutoff valves and check for leaks

How To Replace A Faucet Aerator

If you have noticed a drop of water pressure or an irregular flow from the faucet you may need to replace it and for that follow the simple guidelines to replace the aerator and aerator housing. To find the right aerator you can contact the manufacturers or search online stores.

  1.  First, place a cloth over the top of the aerator housing and use channel lock pliers to gently unscrew the unit. This will stop the housing from bending out of shape or being scratched
  2. If you have recessed the aerator unscrew it by using the provided tools
  3. Remove the old aerator along with the rubber gasket
  4. If the gasket sticks inside the faucet, use the needle-nose pliers to pull it out
  5. Pop the new aerator into the housing and replace place the new gasket 
  6. If you are replacing both the aerator and the housing then grab your new unit
  7. Finally, screw the housing back on and hand tighten

How To Replace A Kitchen Faucet Stem 

  • Shut off the water and take off the set screw with the Allen wrench and take off the handle
  • Unscrew the decorative cap simply with your hands
  • Loosen the stem nut with a channel lock and pull it out. Usually when there is a fault in the cartridge or if the stem breaks off you’ll need to replace both the parts 
  • Now take out the old cartridge and replace it with a new one with a new stem just in place
  • Lastly, reassemble the faucet stem the same way you took it apart

How To Replace A Bathroom Faucet And Drain (4 Easy Steps)

There are a couple of reasons for which you might need to replace your bathroom faucet and drain for like, it might have loose joints or problems in the drain hose. So it fixes that you might want to take a look easy solution we discussed here.

Step 1: Old Faucet Removal

Start by turning the water supply off, place a towel underneath and undo the connections. Now you need to remove the ball rod assembly before removing the old faucet. Unscrew the nuts underneath which holds the faucet with the sink and pull out the faucet. Make sure the new faucet fits in the sinkhole. 

Step 2: Install The New Faucet

Add a bead of silicone caulk around the faucet gasket. Now set the new faucet in place. Take the faucet wing nut and screw it on from underneath the faucet. Wipe off the excess silicone. Now connect the water supply lines using an adjustable wrench and test the sink. Make sure the connections are tight and turn on the quarter-turn valve. 

Step 3: Old Drain Removal

Undo the compression nut so you can slip the whole joint off. Pull down the drain tube and the compression nut. Loosen the thumbscrew on the clevis strap. Now use a wrench to loosen the jamb nut and remove it from the tailpiece. Then remove the drain flange and the drain stopper. Push up the drain assembly from under the sink. Lastly, scrape off the old putty and clean the drain hole. 

Step 4: Install The New Drain

Apply plumbers putty to the drain hole. Remove the top piece of the new drain assembly. Screw the drain tailpiece into the flange underneath. Align the port for the drain lever to the rear and tighten the jamb nut by hand. Remove excess putty. Install the drain stopper. Insert the drain control rod into the faucet and the pivot rod. Attach clevis strap and spring clip. Test the drain. 

Final Verdict

With all the questions being answered and solutions are given in detail, we now hope you’ve finally got every piece of information that you need to learn how to replace a kitchen faucet with a sprayer and now are confident enough to do the task on your own without needing the help of a plumber.

Frequently Asked Questions(FAQ)

How Do You Replace A Kitchen Faucet With A Side Sprayer?

If your kitchen sprayer has seen better days it’s probably time for an upgrade. Replacing it is an easy DIY project that will only take an hour or so. For this job, you’ll need a kitchen sprayer, adjustable wrench, plumber’s putty, and some rugs. 

  • First, turn off the water at the shutoff valve or your main water supply valves and open the sink faucet to drain out any water left in the lines
  • Now remove the old side sprayer assembly by disconnecting the hose from the bottom of the faucet. Then take out the old sprayer hose
  • Underneath loosen the mounting nut that connects the old sprayer to your sink. Then remove the assembly
  • To install the new sprayer applies a ¼ inch bead of plumbers putty along the bottom edge of the sprayer base then place the sprayer’s tailpiece into the deck opening underneath 
  • Then secure the new sprayer with a friction washer and screw the mounting nut on. On the top side be sure to wipe away any excess putty from around the base
  • Next, attach the new sprayer hose to the connector nipple located at the bottom of your faucet
  • Lastly, when the installation is complete turn the water back on to make sure the new connections are leak-free

Can I Install A Sprayer On Any Faucet?

Yes, you can add a sprayer on any faucet you want, and surprisingly it costs you less money to have a separate sprayer in a mixing valve. This will act as a second faucet in your kitchen. The new sprayer hose can be adjusted for only cold or hot or a mixed water supply. 

How Do You Install A Sprayer On An Existing Faucet?

To install a sprayer the first thing you’ll need is a faucet that supports the sprayer attachment and also has at least a separate hole in your sink where the spray will be placed. A mixer valve is also necessary to get hot and cold water mixed at a certain temperature. Then all you need is to follow the steps we’ve mentioned in the next answer. 

How Do You Install A Kitchen Faucet With A Pull-down Sprayer?

To install a pull-down kitchen faucet follow the steps down below:

Step 1

The first thing you’ll need is a deck plate with threaded rods in it. Now before you install this you’ll have to use a bead of silicone roll down to the premier of the faucet holes. 

Step 2

Now place the faucet base into the sink and use plastic lock nuts to secure it. Now it’s time to install the main body of the faucet. Use Teflon tape on the flexible lines. Slide the spray hose down first.

Step 3

No position the faucet in place and now it’s time for the lock nut and washer to be secured from underneath. Position your bracket so that the hose goes inside. Tighten the nut and the bracket in place. 

Step 4

Now you have to attach the spray hose but make sure the Teflon is nicely wrapped. Secure that in place with a wrench. Make sure you install the weight on the hose side that you’re going to pull out which is approximately two inches up from the bottom of the hose. Use a screwdriver to tighten Botha the screws. 

Step 5

Next, you have to attach your water supply lines. First hand tightens then use a wrench. When you are done installing, remove the spray head and turn the water on and let the water run through for a minute. Then put it back into the washer and thread it back on. 

Can I Replace A Kitchen Faucet Myself?

It is a very simple task to be handled by anyone if they know the proper steps and the right tools. That means yes you can surely replace a kitchen faucet yourself.

Can You Replace A Faucet Yourself?

Yes, you can replace a faucet yourself with the proper tools if you know the right technique.

Can You Change The Kitchen Faucet Without A Plumber?

Replacing any kitchen faucet is such an easy job that anyone can do it. In the plumbing section, this is probably the easiest one. So you don’t need a plumber to change your kitchen faucet, just gather the necessary tools and follow the instructions we’ve mentioned here.

How Do You Replace A Kitchen Sink Faucet?

After you take out the old faucet you have to start with the batting order where you’ll have to start with the gasket assembly. Insert the rubber gasket through all the hoses and then insert the plate. 

Now add some putty underneath the plate. Insert another gasket under the plate. To make the faucet attached to the sink you need to insert the metal washer with the gasket underneath the sink and tighten the three screws on it.

This will pull down the faucet squeezing out the extra putty. Now set up all the settings under the sink. Pull the spout out of the spring hose if it does not come back add weight to that. 

Lastly, connect the hot and cold supplies and make the compression connection. Turn on the water to check for any leaks and you are good to go. 

How To Replace The Bathroom Faucet Valve?

To replace a faulty bathroom faucet valve you could just start by shutting off the main water supply to your house. With the main water supply shut off, place a towel underneath to grab any extra water in the mite. Undo the compression nut with a wrench and loosen it counterclockwise. Pull the supply tube out of the valve.

Use a wrench on the bottom of the valve to hold it secure and with a plier break the body of the valve loose from the nut. Once the valve is loose, spin the valve out of the nut counterclockwise. The old valve will come right off.

With the new valve out of the box remove the compression nut and the compression sleeve from the bottom of the valve. Now hand thread the valve into the old compression nut. Once the bottom nut is snug take a wrench and a plier tighten the compression nut. Now attach the dolly lines into place. Lastly, turn on the main water supply.