How To Install A Utility Sink Next To Washer | 7 Easy Steps

Utility sink enhances the beauty of your laundry room or garage area.

To install a utility sink in your laundry room you need to know how to install a utility sink next to the washer. By following some easy steps you can install your sink next to the washer.

In a very short time, you can complete the task by yourself.

How To Install A Utility Sink Next To Washer – Easy Step You Need To Know

How To Install A Utility Sink Next To Washer

You may think it is hard to install a utility sink next to the washer. Do you know?

By following some easy steps, you can install a utility sink next to the washer by yourself. Follow the given step-by-step proves and install your utility sink.

Necessary Tools That You Need

Before installing a utility sink next to the washer, you need to collect some necessary tools that will be needed during the job.

  • PVC Y-fitting
  • PVC hand saw
  • De-burrer or small piece of sandpaper
  • Two brass pipe splitters
  • Wrench
  • Pliers
  • Threading tool (optional)
  • Plumber’s glue
  • Hot and cold flexible tubing
  • Measuring stick

After collecting all the ingredients, you can start your installation process.

Step 1: Turn Off The Water Supply Line

Before installing the sink, you need to make sure that you have turned off the main water supply.

If you do not turn off the water supply line, then water will spread all over the kitchen area. 

Step 2: Measuring For Drain

Measure how far the drain pipe connection is from the ground. Locate your existing washer’s drain line, specifically where it goes down into the floor or wall.

Take the same measurement of the utility sinks drain line and make a mark on your washer drain line.

In this place, you will set the new Y-fitting that will separate the washer’s drain from the utility sink’s drain in the next step.

Step 3: Cutting and smoothing drainpipe

The mark you have made, cut the existing drain pipe from the mark to anywhere on the venting pipe that connects above it. You also need to cut the horizontal T-fitting from where the washer turns downward toward the exit drainpipe.

Now it is time to smooth out the insides of the pipe where you cut it. Use a tool or piece of sandpaper to deburr or smooth the pipeline.

You need to make sure that there are no rough or uneven edges when you attach pipes in the next step.

Step 4: Attaching Y-fitting And Adding Laundry Sink

Take the PVC Y-fitting and attach it to the existing drain pipe. Attach one arm of the Y to the horizontal flow of where your washer drain exists. Fix the top of the Y-fitting to the venting pipe above.

And the other arm of the Y-fitting will attach to a pipe that runs from your utility sink drain.

Fix them tightly, using plumbers putty or glue. Make sure that all are waterproof and secure. 

Step 5: Locating Water Sources

Now it is time to locate the hot and cold water pipe connections near your washer. These run to a single fitting on the water pipe. Disconnect the water pipe at the point on each of the hot and cold hookups.

If you fail to connect the fitting and the size of the pipe is longer than necessary then you have to cut the pipe. Place a bucket so that water drops do not fall onto the floor.

Cut the pipe in the midway between the washer and utility sink. If you need to sew the pipe at this point, then do it using the threading tool. 

Step 6: Adding Pipe Splitter

Screw the splitter onto the main water pipe using a two-headed brass pipe splitter. You need to make sure that the seal is complete and you screw this one tightly.

To make sure the connection is secure, use a wrench. Now the splitter will separate the water supply from the hot and cold pipes.

One line of the pipe will go to your washer and one will go to your sink. Make sure that you attach the splitter to both the hot and cold water pipes. Reconnect the washer with the existing pipes, after securing the splitter onto the hot and cold water lines. 

Step 7: Connect Hoses

Connect the flexible tubing from the pipe splitter to the sink’s hot and cold lines. Adjust a red tube for hot water and a blue tube for cold water. Make sure that you hoot these up to the appropriate pipe. Using a nut, tight these connections. 

Final Verdict

We hope that you have your answer on how to install a utility sink next to the washer. It is simple and easy if you can follow the step-by-step process.

After completing the task, turn on the main water supply. Check for leaks and make sure water runs smoothly and quickly.