How to clean a corroded faucet occurs for several factors including, hard water and environmental factors for instance temperature.
Corrosion of faucets has been a great challenge and it is difficult to clean if you do not know the right process of cleaning.
- The 8 Best Sink Protector Review For 2021 (Updated)
- The 14 Best Kitchen Sink Reviews In 2021 (Updated List)
- The 8 Best Pedestal Sink For Small Bathrooms For 2021
- The 7 Best Bathroom Vanities For Small Bathrooms
- Moen Vs Delta Kitchen Faucets: H2H Comparison
- How To Fix A Leaky Kitchen Faucet Single Handle
- 6 Easy Steps Of How To Remove Kitchen Faucet Without Basin Wrench
- How To Disconnect Sprayer Hose From Delta Faucet
The rust makes your faucets seem dusty. Due to the corrosion, your kitchen faucet may not give you good performance.
How To Clean A Corroded Faucet – 5 Easy Methods
This article will let you know various ways of how to clean a corroded faucet. You can apply any of them to clean the faucet.
Method 1: Using Undiluted White Vinegar Solution
Vinegar is the best cleaning agent among all cleaners. This cleaning material is efficient for almost all cleaning tasks. It is very easy to clean a corroded faucet using vinegar.
All you need to do is pour the vinegar solution into the small basin and let it soak the rusted parts in the solution. After a while, wash it with clean water and dry it.
If you cannot dismantle the faucet, there is nothing to worry, follow the simple process below for cleaning the corroded faucet.
- Take one or two cups white vinegar
- Pour them into a plastic bag
- Wrap the bag filled with vinegar on the spout. Make sure that you hold the bag at an appropriate angle to flows the white vinegar into one corner
- Leave it for 24 hours to achieve the best results
- Untie the bag
- After the time is up, pour the vinegar into the drain, as it got no effect
- Take an old toothbrush and scrub the affected area
- Put more effort on the most corroded areas and ensure you scour all parts
- Rinse the faucet with clean water
- Take a clean cloth or towel and dip it in cold water. Rinse the faucet until all the dirt is gone
- Using another dry cloth, dry the faucet
Method 2: Applying Oxalic Acid
If your faucet is full of corrosion then oxalic acid is going to help you to get rid of this problem. Applying the oxalic acid, you can clean your corroded faucet and give it a new look.
When you are cleaning your faucet with oxalic acid, you need to be cautious, as it is a potent chemical agent. Wear protective clothing, probably rubber gloves, to avoid hurting your hands.
Another thing you need to make sure that you do not breathe in the acidic fumes as it can cause you excessive problems. Maintaining all the caution, you have to start the cleaning task.
- Mix 250ml water with 25 ml acid and make a diluted mixture
- Pour out the mix on your corroded surface
- Leave it for around 30 minutes
- After the set time, wash the faucet thoroughly
- Get a piece of clean cloth and dry the faucet
Method 3: Using Wd 40
WD 40 is very useful for various jobs but is an essential treatment for corroded faucets. You will get it in most of the shops. Grab yourself one and see the significant change in your faucets.
You can also apply the WD 40 on the taps to prevent corrosion from retaking. Let’s know how you can clean corroded faucets using the WD 40!
- Wipeout any dirt that could be on the tap with a clean cloth
- Spray all over the rusty faucet with WD-40.
- Scrub the faucet with a clean wire brush
- Get clean water and rinse the faucet
- Dry the faucet with a dry cloth or towel
- WD-40 will leave your faucet looking almost new again
Method 4: Using Citric Acid
Citric acid is very useful to clean corroded faucets and you will get it in any shop.
- Get a plastic container and pour in your citric acid
- Pour it out on your corroded faucet
- Leave it for around 45 minutes
- Wear rubber gloves and scrub the faucet surface thoroughly
- Once done with scrubbing, rinse it with clean water
- Dry up the faucet with a clean cloth
Method 5: Applying Lemon Juice Paste
To make the paste, you need salt and lemon juice. If you are cleaning the faucet for the first time, it will be very helpful for you.
- Use a clean cloth or warm water to clean
- Sprinkle salt over the corroded faucet and make sure it is fully covered
- Squeeze your lemon juice all over the faucet surface
- Leave the paste for 2-3 hours before cleaning
- Clean by gently brushing the areas with a soft brush
- Wipe the paste off and using a clean cloth
- Dry it off
If you want to get a new look at your faucet, you should know how to clean a corroded faucet. After knowing the cleaning process, apply them to the faucets to clean the corroded surface.